Calibrated for 36V / 48V / 52V / 60V / 72V Li-ion & LiFePO4 packs, Bosch/Bafang/Shimano drive units, and Ninebot/Xiaomi scooters.
Select battery pack & enter current display/multimeter voltage:
Real-time physics calculators accounting for Peukert sag, cold weather derating, CC/CV charge phases, and rider weight.
Compare manufacturer hype vs actual road range across 24V–72V batteries, rider payload, hill grade, and winter temperatures.
Calculate exact fast-charge time to 80% (CC stage) vs 100% balancing (CV tail), C-rate safety, and electricity cost per charge.
Exact front & rear PSI/Bar calibrated for rider weight, 8.5"/10" scooter tires, 20x4.0" fat bikes, and wet/gravel tarmac.
Calculate off-grid appliance runtime, DC amp draw, BMS sizing (100A/200A), and solar panel wattage for LiTime & EcoFlow banks.
The only reference matrix featuring both Resting Open-Circuit Voltage and Dynamic Riding Load Sag.
A standard 36V (10S) e-bike/scooter battery charges to 42.0V (100%) and cuts off at 30.0V (0%). A 48V (13S) battery charges to 54.6V (100%), reaches 50% at 48.8V, and cuts off at 39.0V (0%). A 52V (14S) pack reaches 58.8V (100%) and cuts off at 42.0V.
| System Nominal | Series Config | 100% Full Charge | 80% Daily Cap | 50% Winter Storage | 20% Recharge Warn | 0% BMS Cutoff | Full Chart |
|---|---|---|---|---|---|---|---|
| 36V Li-ion (10S) | 10S (Li-ion) | 42.0V | 39.7V | 37.5V | 35.1V | 30.0V | View → |
| 48V Li-ion (13S) | 13S (Li-ion) | 54.6V | 51.6V | 48.8V | 45.6V | 39.0V | View → |
| 52V Li-ion (14S) | 14S (Li-ion) | 58.8V | 55.6V | 52.5V | 49.1V | 42.0V | View → |
| 60V Li-ion (16S) | 16S (Li-ion) | 67.2V | 63.5V | 60.0V | 56.2V | 48.0V | View → |
| 72V Li-ion (20S) | 20S (Li-ion) | 84.0V | 79.4V | 75.0V | 70.2V | 60.0V | View → |
| 48V / 12V LiFePO4 (16S / 4S) | 16S (LiFePO4) | 57.6V | 53.4V | 52.3V | 50.9V | 40.0V | View → |
Step-by-step multimeter & connector repair trees for Segway-Ninebot, Xiaomi, Bosch, Bafang, and Shimano Steps.
Abnormal throttle accelerator signal voltage (outside 0.8V–4.2V Hall sensor bounds) or lever stuck during boot.
Brake lever Hall sensor signal is out of calibration range or magnet has detached inside the brake handle.
Main ESC controller receives no serial telemetry data (TX/RX) from the Battery Management System (BMS).
Drive unit senses motor torque and cadence while riding, but receives zero magnetic pulses from the rear wheel speed sensor.
Motor controller algorithm detected implausible ratio between wheel speed pulses and crank/motor RPM (tuning chip or magnet interference).
Controller input voltage exceeds upper firmware threshold (commonly 58.8V full 52V pack plugged into a 48V-only programmed controller).
Display powers on from battery voltage, but serial UART/CAN communication lines (Green/Yellow wires) between display and motor controller are interrupted.
Drive unit torque strain gauge could not calibrate zero-offset during startup because rider foot pressure was resting on the pedal.
Xiaomi M365, Pro 2, 1S, 3, and 4 Pro throttle (14) or brake lever (15) Hall sensor voltage out of range.
Exact replacement tire ETRTO sizes, brake pad compatibility codes, and charger connectors for popular rides.
Tire: 10 x 2.50" (60/70-6.5 Tubeless Self-Healing) (45/50 PSI)
Pads: Ninebot G30 110mm Drum Brake Shoe Assembly
Charge Port: Internal 3-Prong Mickey Mouse AC (C5) + RCA 8mm DC (42V Max 5A)
Tire: 8.5 x 2.0" Pneumatic Tube (or 10" CST Upgrade) (48/53 PSI)
Pads: 18mm Round Resin Disc Pads (Xiaomi M365/Pro 2 Standard)
Charge Port: RCA 8mm Coaxial DC Plug (42.0V 1.7A–2.0A)
Tire: 20 x 4.0" Knobby Fat Tire (20/22 PSI)
Pads: Shimano B01S / B05S Compatible Rectangular Resin Pads
Charge Port: DC 5.5 x 2.1mm Barrel Jack (54.6V 2.0A–3.0A)
Tire: 20 x 3.0" Puncture-Resistant Slim Fat Tire (30/32 PSI)
Pads: Shimano B01S / Tektro E10.11 Ceramic/Sintered Pads
Charge Port: DC 5.5 x 2.1mm Barrel Plug (54.6V 2.0A)
Tire: 29 x 2.40" / 27.5 x 2.60" eMTB Tubeless Ready (26/29 PSI)
Pads: Shimano D03S / N03A Finned Resin or Magura 8.P
Charge Port: Proprietary Bosch Oval 4A / Smart System Rosenberger Plug
Tire: 27.5 x 2.35" Schwalbe Marathon E-Plus (38/42 PSI)
Pads: Shimano B05S / MT200 Hydraulic Pads
Charge Port: XT60 / XT90 Discharge + GX16-3 (3-Pin Aviation) Charge Port
Instrumented load tests measuring real Wh/km consumption, controller voltage sag, and 3-year maintenance costs.
We hooked a multimeter and inline wattmeter to the two bestselling 48V folding fat-tire e-bikes in Europe and America to measure real Wh/km consumption, BMS cutoff, and brake pad wear.
Long-term workshop teardown and battery degradation test of the world's most reliable commuter scooters: real range at 25–32 km/h, suspension upgrade value, and Error 14/15 prevention.
Capacity discharge bench test of Grade-A prismatic LiFePO4 packs for solar off-grid cabins, RV campers, marine trolling motors, and heavy cargo trikes.
High-retention technical playbooks on winter storage, UL94 fire safety, and lithium cell chemistry.
Storing a lithium-ion pack at 100% or 0% over winter permanently destroys 15%–28% capacity. Use our resting voltage table and fireproof storage checklist.
Charging your 48V battery to 51.6V–52.8V (80%–90%) instead of 54.6V (100%) cuts cell stress in half and increases lifespan from 500 to 1,200+ cycles.
Small 8.5"/10" scooter tires lose 2–4 PSI every week. Riding at 25 PSI instead of 45 PSI spikes rolling resistance by 20% and causes instant snakebite tube punctures.